Cyberoce QR code door access control Configuration Tool, merges multiple configuration codes into one ——Let system integrators bid farewell to the hassle of multiple QR code scanning configurations on construction sites

Author: Tang Zhenhao

Table of contents

I、The role of QR code door access control configuration tool in secondary development docking

II、The role of one click configuration of QR code door access control in practical project applications

III、The specific steps for merging multiple configuration codes into one using QR code door access control are as follows

Text:

The Cyberoce QR code door access control configuration tool is tailored for system integrators or software platforms with development capabilities.

I、The role of QR code door access control configuration tool in secondary development docking

1. Hardware configuration and debugging

Developers can set basic configurations such as the address, networking mode, communication protocol, and screen parameter settings for QR code door access control and system backend connection with just one click through a graphical interface, without the need to send instructions one by one through code or serial port, greatly reducing the time for secondary development.

2. System integration and testing support

Before docking with the self-developed system, use a configuration tool to verify whether the various functions of the Qr code door access control hardware are normal (such as scanning code recognition, network communication, etc.).

3. Enable the necessary features for the project

Different projects have different requirements for access control functions (such as whether password verification is enabled, whether IC card sector encryption is enabled, whether devices use separate configuration passwords, etc.). The configuration tool provides corresponding functional options based on device models to ensure that developers can access all hardware functions.

II、The role of one click configuration of QR code door access control in practical project applications

Our company's QR code door access control configuration can also merge multiple configuration codes into one configuration code. For example, in practical projects, a QR code door access control all-in-one machine requires multiple configuration requirements for installation and debugging:

1. The backend server address is: https://www.sz-cerberus.net
2. The communication protocol used is HTTP protocol
3. The networking mode is WIFI, the username for WIFI is cyberoce, and the password is 123456
4. The door opening logic is: scan the code and then delay for 3 seconds to close the door
5. The screen standby text is: welcome

If each item generates a configuration code separately, it needs to be scanned continuously for more than 5 times on site, which is not only cumbersome to operate, but also prone to omission or disorder of order. More importantly, in the scenario of cross-border bulk deployment, this fragmented configuration method can easily lead to inconsistent device status, increasing the cost of after-sales service in the later stage. By using the cerberus configuration tool, a unified configuration code can be generated with just one click.

III、The specific steps for merging multiple configuration codes into one using QR code door access control are as follows:

1. Open the configuration tool and select the specific QRcode door access control model number. If CR07EU is selected, click on the CR07EU icon to enter.
   
2. Merge the above 5 configuration codes into one configuration code. The specific steps are as follows:

A、 In the CR07EU configuration interface, click on Network, select the asterisk "☆" in front of the address, and enter www.sz-cerberus.net in the address bar,

B、 Select HTTP Mode and check the asterisk "☆" before the mode,

C、 Select the asterisk "☆" in front of Networking mode, and also select WIFI. Fill in "cyberoce" for "name" and "123456" for "Password", and also select the asterisk "☆" in front of it,photo as below:

D、 Set the Door opening delay to 3000ms in the Verifying menu bar and select the asterisk "☆" in front of it,photo as below:

E、 Select the asterisk "☆" in front of Standby text in the Screen menu bar and fill in "welcome",photo as below:

At this point, the configuration combination of A-E has been set. Next, click on Custom to check for any missing items in the Configuring Device Parameters. If there are no missing items, the configuration code on the left will be the combined code of the above 5 configuration codes.Photo as below:

By scanning the unified merge code once on site, the equipment can complete all parameter writing and automatically restart within seconds, greatly reducing the workload of on-site construction personnel and improving work efficiency.

Revised by: Zhao Kai

Translated by: Michael Shao